19 Year-Old James Tuchel Creates H2O Hybrid Vehicle

James Tuchel, a 19 year-old from Grand Bahamas, has developed his own water powered hybrid car in less than 2 months using local suppliers and materials.

According to James, the car uses the properties in drinking water to increase fuel economy by up to 30 % while dramatically reducing harmful exhaust emissions.
The H2O hybrid vehicle uses a 12volt battery to separate drinking water into two useful elements (oxygen and hydrogen) that fuel the internal combustion engine.
The hydrogen from the electrolysis boosts the internal combustion process as it combines with gasoline entering the engine. Since the car relies on more than one fuel source or energy conversion device, it becomes a hybrid.
For the future, James plans to make the vehicle run entirely on water, without any gasoline.
Because the internet is full of plans sold by scammers, nowadays you don’t really know who is legit in making such claims as to reduce the fuel consumption to such an extent. Still, let’s hope James’ is real and that we’ll hear about it in the future.

Akridge Energy Buys 400 MW Free Energy Generator from BlackLight Power

I know it may sound like science fiction, but if you remember we talked about BlackLight Power’s invention last year, you surely do remember it was about free energy. BlackLight’s hydrino (a hydrogen atom with a lower energy state  than it was previously thought possible) stirred controversy in scientists’ world, bringing them bad fame as seekers of “free energy” and associating BlackLight Power with a scammer’s image.

On July 30, BlackLight Power announced a commercial license agreement with Maryland-based Akridge Energy. BLP will allow Akridge to use their energy producing process for generating electricity in Maryland, Virginia and the District of Colombia, up to a maximum continuous capacity of 400 MW.
“We believe BlackLight Power has developed a new energy technology that will have a profound impact on the environment and the economy and will help us achieve our goal in becoming a major, green-power producer in the greater-DC market,” said John E. Akridge III, chairman and owner of Akridge Energy. “We are excited to be one of the early-adopters of BLP’s energy technology.” Mr. Akridge is also a shareholder of BlackLight Power.
The trust that Akridge Energy is giving BlackLight by investing in them should give the science community a reason to think more about hydrinos and accept newer physics concepts that, even if not fully understood and demonstrated, work. We’ll keep you updated with any other news about BlackLight’s evolution.

Of all the subjects in the alternative energy wor...

Of all the subjects in the alternative energy world, I liked the “Free Energy” part best. It’s not that I’m an absurd non-science, self-proclaimed geek, but I like to give a chance to new ideas of changing the world, and I still strongly believe we’re not being told everything.

Following this thought, magnets have always fascinated me (like I think they did to any science interested human), and I always had the sensation there’s more to them than just their capacity of simply attracting or repelling an object.
I remember once (I was about 8 years old) I struggled an entire day trying to understand why if I put one magnet on a small toy car this would only move only if I kept the other in my hand. The explanation came a few years later, when I rethought it.
What you are going to see in this video is nothing you don’t know. In fact, I urge any weird-science reader to try and make the device from the video below, respecting the pictured details. I’ll make it myself from a hard drive plate and a used scotch tape support. Let’s see how much time it works, and if it can be improved.
Magnetic energy isn’t really “free energy”, nor it harnesses zero-point energy, because magnets themselves are losing their magnetic ability over time, but that time is a very, very, very long one (someone said four hundred years). So, it doesn’t cost us  much to first test, and make theories after! I know some will say “it’s stupid, my high physics knowledge doesn’t let me try this thing”. When it comes to you to say that, think that you’re only limiting yourself from touching and convincing yourself one way or the other of the theory. Just don’t let it pass by you without a trial.
The magnetic motor video below is pretty amazing.

How To Build A Free Energy Magnetic Water Heater

This heater is related to the transformation of magnetic energy and certain gases directly into heat energy without the use of ignition, as we know it.

It is a heat-producing device that will greatly reduce atmospheric pollution and conserve energy. This device includes two spherical hollow pressure chambers that are joined together at a mixing junction at which point heat exits the device.
SUMMARY OF THE UNIT
This heater utilizes the blending of a light gas with a heavy gas activated by flowing magnetic current to create heat. This newly formed heat energy is created through a very particular blending of magnetized molecular structures, that when combined and mixed with air, manifest as heat without ignition or spark.
CONSTRUCTION DETAILS TO PRODUCE A MAGNETIC HEATER
Viewing Figure 1 shows two eight inch dia. spheres with one located two inches above the other. These spheres are made of 1/8 inch thick TiAlCo-B metal; a metal that welcomes magnetism yet is NON-magnetic (meaning a magnet will not adhere to it). Each sphere is made in two halves which when assembled into an 8 inch ball, become a chamber able to hold an interior pressure. Thus the two halves are joined by compressing an ‘O’ ring seal.
To set a required magnetic polarity to the upper sphere, this sphere is completely covered on the outside surface with one layer of 92 thousandths thick powerful plastic magnet material. This magnet material is all of the same polarity on the side contacting this upper sphere. Just for identification purposes we will say the polarity is all of a NORTH charge.
Located in the center of this sphere is a 3 inch dia. copper ball, polished on the outer surface, and held in place by non-metal support rods. Through the use of a coaxial cable, a magnetic current generator sends neutral magnetic current directly to this copper ball. This cable, when passing through the 1/8 inch thick TiAlCo-B sphere, is insulated and sealed to allow the sphere to hold an interior pressure. The proper coaxial cable to use is one that has a copper coated steel wire in the center. Magnetic current will not flow properly into a solid copper wire. We need to think of the copper coating (on the steel wire) as serving the purposes of allowing the magnetic current to flow in both directions simultaneously.
This upper sphere is then pressurized with about 15 pounds per square inch of a light gas which fills the sphere from the top location (see Fig. 1). This gas supply is a standard bottled gas unit.
While there are several light gases one might use, one suggestion is to use a pale pink gas to charge this upper sphere. We need not be concerned that this is a gas type heater in that the gas only serves the purpose of a catalyst. The actual amount of gas being used is very minute with the magnetic current being the primary heating source of energy.
When the light gas has charged this upper sphere, it is at this point that magnetic current is fed to the center copper ball. The neutral magnetic current’s very nature is to seek a polarity. The gas then serves the purpose of allowing the neutral magnetic current to cross the 2-1/2 inch space distance and grab a north polarity from the 92 thousandths (.092) thick plastic magnets. The polished surface of the copper ball and the inside polished surface of the TiAlCo-B sphere cause a back and forth bouncing action for this magnetic energy flow. This activity builds into a pressure which will be released when the pressure control valve is opened (see valve on Figure 1).
These newly formed combinations of particles have a NORTH charge and the light gases interior pressure is amplified by the gas susceptibility to the incoming magnetic current. The TiAlCo-B sphere is a material, which has a high magnetic permeability, which also enhances the NEEDED particle interchange process.
At the same moment in time, the bottom sphere is also charged with a gaseous and magnetic current. The bottom sphere is charged with a heavy gas formed by combining two different gases. The bottom heavy gas combination needs to balance with the upper light gas, thus ultimately one must use 2/3 less heavy gas then the light gas IN VOLUME. This heavy gas might be a combination of hydrogen and a gas, which will cause the mixture to be LESS combustible.
As this heavy gas combination is caused to enter this bottom sphere a bleed-off valve located at the upper part of this lower sphere, allows air to be pushed out until only heavy gas is inside this lower sphere. After gas is inside this lower sphere, the flowing magnetic current is sent into the lower 3″ copper ball. The lower sphere has the same plastic magnet covering; however, the charge facing the sphere is all a SOUTH charge. Because of this opposite polarity charge, the mixture of energy from the upper sphere, becomes a massive ATTRACT charge to the lower sphere’s energy charge.
To start the heating process, the valve under the upper sphere is opened, as well as the valve at the top of the bottom sphere. These magnetic molecular structures instantly join on attract inside a short mixing chamber. At this moment, NO heating has taken place. Next, an air blower is activated which pulls these blended particles out of the mixing chamber and causes them to be mixed with air. The instant air is added it causes a nuclear chain-reaction, which spreads through these blended magnetic molecular structures causing a release of energy in the form of heat. The amount of air is controlled so as to become a temperature adjustment tool. For example, to send the flow into a home heating duct system a certain air volume is required; however, to send the heat under a container to boil water, a different amount of air is needed. While the heating is adjustable, there is never ignition into spark as is common with BURNING heating systems.
Both spheres are fed a continuous but MINIMAL amount of bottled gas because, as stated, the gas serves the purpose of being a catalyst for the incoming neutral magnetic current.
One might wonder why one bowl is located directly above the other. The reason is that the upper bowl can maintain a full charge of gas because this light gas will only exit the upper sphere when the sphere is full. Also, the bottom sphere, having a heavy gas combination, fills the sphere up to the top. With this arrangement, the incoming neutral magnetic current always has a conduit of gas to then get attracted to its given polarity.
This action of forming heat is the result of a nuclear chain reaction whereby each fission initiates further fission’s resulting in the release of energy that is manifest as RADIANT heat. There is NO substantial heating until the mixture is blended with air.
The location for this unit to heat a home would be in the standard position, which takes into account that heat rises, thus requiring the needed heating duct system.
PARTS LIST:
1. Is an outer non-metal frame to hold spheres and an air blower.
2. Upper sphere 8″ inside dia., 1/8 inch thick made of TiAlCo-B metal (polished on
inner surface).
3. One ‘O’ ring seal to join two halves which form a sphere.
4. An outer layer of 92 thousandths (.092) thick plastic magnet material having
all one NORTH polarity facing inward.
5. Is a 3″ copper ball, polished, firmly held in the center of the sphere with non-metal rods.
6. A coaxial cable wire insulated from Part #2 and firmly secured to Ball #5.
7. An exit pipe having a pressure type needle valve, which controls the energy
flow out of Part #2.
8. A bottle of light gas which is pale pink in color connected to flow into Part #2.
9. Support braces to hold sphere #2 to frame #1.
10. Is a bottom sphere 8 inch inside diameter, 1/8 inch thick made of TiAlCo-B metal, also polished on the inner surface.
11. An ‘O’ ring seal to allow pressure inside Part #10.
12. An outer layer of .092 (92 thousandths) thick plastic magnet material having the SOUTH face inward toward the TiAlCo-B metal.
13. A 3 inch copper ball, polished, held in the center of part 10 with non-metal rods.
14. A coaxial cable wire insulated from Part 10 and firmly secured to Part #13.
15. An exit pipe on the top of Part #10 having a pressure controlled needle valve
to regulate the flow of energy out of part #10.
16. A bottle of a combination heavy gas to flow into #10.
17. A mixing chamber to allow the NORTH charged gas from part 2 to blend
with the SOUTH charged gas from part #10.
18. Are vent holes to allow air volume to be adjusted as needed.
19. A standard heater type air blower used to pull the blended energy mixture out of chamber 17, cause it to be mixed with air, then drive the heat to areas requiring heating.
A tremendous amount of electricity is generated to provide people with heat. Electricity production generates pollution and harmful energy fields that damage the environment and all life. It is time that people use safe, renewable resources that do not create pollution and that recycle the free energy used. Please share this information with others.

How to make electricity with magnets for free

How To Build a Free Energy Generator (Mini Romag)

The Mini Romag free energy generator from Magnetic Energy uses the principle of moving magnetic flow named “the magnetic current” for generating electrical power. According to Magnetic Energy this generator is able to produce 3.5 volts, 7A DC ( about 24 Watts ) of free electricity while its generate sufficient power to sustain itself…

This generator need to be started by an external motor during about 42 seconds at 2100 RPM. After this charging process, when the energy flow is established in the Romag generator, the motor can be removed and free electrical energy can be used.
The Romag free energy generator is a new revolutionary concept which generates electrical energy without using the first flow of current generated by magnetism, it uses only the untapped natural resource of the magnetism…
HOW THE UNIT WORKS :
The here disclosed 3½ volt, 7 amperage magnet motor/generator must be charged up by driving the main shaft at 2100 RPM for 42 seconds. This charging process manifests as magnetic energy within the six coils of copper wire, the copper tube supporting these coils and the copper coated steel wires wrapped around the magnets. This charging is accomplished while the six coil connection wires, Part #22, are making contact and setting up their alternating magnetic poles. After the 42 second charging time one of these coil connection wires must be opened and this circuit again completed through an energy draw at what could be called 7 amps. See load Part #23. As current is drawn from the six coils, this draw sets up magnetic poles which are a response between the rotor magnets and the coils. This response then causes the main shaft to be rotated by the 12 permanent magnets as they attract and build a release field. Then the driver unit (hand crank) is disconnected allowing the unit to rotate with the load being the activating driving force.
The fields of the magnets must be maintained during their spin movement. These magnetic fields which are encapsulated are achieved by the wiring system. The attract/release of the magnets is a function of several factors. First, the magnets attract field between north and south is completed by taking a crossing path of attract (top of one row to bottom of next, etc.). This action has the effect of fields blending into fields, and a hold-back attract does not happen. Each time a magnet set passes a coil an interchange of like energy between the coils around the magnets and the generating coils sets-up neutral polarities which are ‘release fields’ and prevents a hold-back attract.
One important magnetic assembly is the circuitry which allows this interchange of free energy. This is a recycling of a stabilized magnetic/electro energy not electro/magnetic because the field of force is not a case of electrical input, an input that created the magnetic energy, but rather a build-up of magnetic energy which caused a free energy thrust.
In further defining the workings of this unit it is important to understand that although electrical and magnetic (energy) work with similar attitudes, the manner in which they work sets-up a differing energy effect. One of these effects is that magnetic structures want to share their f1ow, compatible to the Universal Force, while electrical flow argues, (short circuits, sparks, etc.). Because of this fact the working responses (within the unit) take place, how they are needed, and when they are needed which results in a functioning unit. There is a continuous transmutation process taking place whereby magnetic energy continually generates an energy that manifests a measurable current.



FREE ENERGY GENERATOR PARTS LIST AND CONSTRUCTION DETAILS
When building your first unit we suggest using the stated materials.
1) Aluminum Base Plate
2) Sleave Bearing, 1″ long, ½” inside diameter, oil impregnated brass.
3) 4″ long by ½” diameter Brass Shaft
4) Brass 2″ diameter Rotor, 1-3/4″ long

5) Six rotor slots, each 1-3/4″ long by .260 deep by 23/32″ wide. These slots are spaced exactly 60 degrees apart.
6) One slot cut in center of Brass Rotor, 360 degrees around, ¼” wide by 5/16″ deep.
7) 12 slots (formed from the six slots as the 360 degree cut is made). Each slot is lined with .010 thick mica insulation.
8) A total of 228 pieces of U-shaped .040 thick copper coated steel wires. Each slot (Part #7) has 19 pieces of these wires fitted into the Mica, thus these wires do not contact the Brass rotor. The lead edge of these wires is flush with the Rotor’s outer surface and the trail edge protrudes 1/8″ above the Rotor’s outer diameter.
9) Eleven complete turns of .032 thick copper coated steel wire. These 11 turns or ‘wraps’ accumulate to 3/8″ wide and the same pattern is placed around all 12 magnets. When placed into the bent wires #8, they are a snug fit making firm contact.
10) Are 12 pieces of .005″ thick mylar insulation inserted into the cores of the wires #9.
11) 12 permanent magnets, insulated with the mylar, to not contact wires # 9. These magnets measure 3/4″ long, 5/8″ wide, 3/8″ thick and are made of a special composition and strength. Alnico 4, M-60; 12 AL, 28 Ni, 5 Co, bal Fe, Isotropic permanent magnet material cooled in magnetic field, Cast 9100 TS. 450 Brin, 2.2 Peak energy product. When inserted in the rotor the outer faces of these 12 magnets are not to be machined to a radius. The center of these magnets pass the center of the coils with 3/32″ clearance. The edges, where the wires are wrapped, pass 1/32″ away from the coils. This ‘changing magnet spacing’ aids in not only the release cycle but also contributes to rotational movement. (Sharp magnet edges which are facing the coils are to be sanded to a small smooth radius.)
12) Magnet polarity placement into Rotor.
13) Connection pattern for wires wrapped around magnets. The 12 wire wraps are divided into two sections, upper and lower of six each. There are no connections between these sections. The magnetic flow direction between the upper 6 wraps and the lower 6 wraps is attained by the ‘flow direction’ as shown in Figure 5. Viewing Figure 6 shows the wires wrapped around the magnet starting at the top ‘north’ half and then after 11 complete turns the wire exits at the lower ‘south’ half. As this wire then goes to the next magnet it arrives at an attract wire which is its ‘north’ side. Thus all wires get interconnected from south to north magnet half or north to south magnet half. The actual connections should be crimped copper clips not solder with insulation tubing to prevent contact to the Rotor body.
14) A .030 thick copper tube (stiff material) 2″ long by 2½” inside diameter.
15) Are six slots cut at the top of tube #14. These slots are 5/8″ wide by 1/32″ deep spaced at 60 degrees apart.
16) Are six slots cut at the bottom of tube #14. These slots are 5/8″ wide by 5/16″ deep and in line with the upper slots #15.
17) Six copper tube mounting points.
18) Acrylic ring to hold Part #14, measuring 3-3/4″ O.D., 2¼” I.D., 3/8″ thick bolted directly to Part #1. This ring has a .030 wide groove cut ¼”deep to allow the six copper tube mounting points, Part #17, to be inserted.
19) A .002″ thick plastic insulation paper to be placed around the inside and outside of Part #14.
20) Are six coils of insulated copper wire, each coil having 72 turns of .014 thick wire. Each coil is wound with two layers, the bottom layer to completely fill the 5/8″ wide slot with 45 turns and the top layer to span 5/16″ wide with 27 turns. To be sure each coil has the exact wire length or 72 turns, a sample length wire is wrapped then unwound to serve as a template for six lengths. A suggested coil winding method is to fill a small spool with one length then by holding the copper tube at the lower extension, then start at the plus wire in Figure 2 and temporarily secure this wire to the outer surface of the tube. Next, place the pre-measured spool of wire inside the tube, wrapping down and around the outside advancing clockwise until the 5/8″ slot is filled with 45 turns. Then, return this wire back across the top of the coil for 15/32″ and winding in the same direction again advance clock-wise placing the second layer spanned for 5/16″ with 27 turns. This method should have the second layer perfectly centered above the first layer. After winding this coil, repeat the process by again filling the small spool with another length of pre-measured wire. A very important magnetic response happens as all six coils have their second layers spaced as disclosed.
21) This number identifies the top view of the second layer.
22) Connection pattern for six coils. When the unit is driven at start-up (hand crank) for 42 seconds at 2100 RPM, all six jumper wires must be together which means the plus wire goes to the minus wire connected by the start switch. After 42 seconds the load is added to the circuit and the start switch is opened. To double check your connections between the coils, note that the finish wire of coil #1 goes to the finish wire of coil #2, which is top layer to top layer. This pattern then has start of coil 2 (bottom layer) going to start of coil 3 (also bottom layer). When the copper tube with the coils is placed around the rotor, the distance from any magnet to any coil must be identical. If it measures different, acrylic holding shapes can be bolted to the aluminum base, protruding upward, and thus push the copper tube in the direction needed to maintain the spacing as stated.
23) Wires to load.
24) Wires to start switch.
25) Rotational direction which is clock-wise when viewing from top down.
26) Acrylic dome for protection against elements.
27) Coating of clear acrylic to solidify rotor. Do not use standard motor varnish. Pre-heat the rotor and then dip it into heated liquid acrylic. After removal from dip tank, hand rotate until the acrylic hardens, then balance rotor. For balancing procedure, either add brass weights or remove brass as needed by drilling small holes into rotor on its heavy side.
28) Insulation tubing on all connections.
29) Shaft for start purposes and speed testing (if desired).
This concludes the parts list for the Mini-Romag.
This simple free energy generator demonstrates profound concepts and has a surprising number of applications. Remember, it must have a load to work, something that attracts magnetic energy. Build this unit and explore new possibilities of creating “free energy” yourself!

The Pyramid Effect Producing Enough Electricity to...

The fact that pyramids have peculiar features is well-known worldwide. We are all informed that the seeds found in the Egyptian pyramids were still germinable after thousands of years.

Austrian inventor Flavio Thomas (Trawoger) points out that the energy capture circuits are positioned in the geometric center of the pyramid. The materials that the pyramid is made from are less important for its function.
Thomas uses a stabilizing frame, a condenser plate and a magnet as a converter. When the magnet is taken out, the conversion stops, but can begin again in case the magnet is re-attached to the frame.
The electricity that the pyramid set-up produces helps Thomas run a small fan. It seems that the fan can work for more than 30 days, supplied with the pyramid’s energy. The fan runs on 12 volts and has a maximum absorption of 1.1 Amperes.
Moreover, the orientation of the pyramid plays a major part. The loss of energy production will be improved by a small change in the orientation of the pyramid (an exact north-south orientation causes daily fluctuations of 5 to 8% in the energy output).
There is also a similar, but at the same time a different kind of pyramid, which consists only of metal tubes. If you attach a magnet to it, it will measure 22 volts, 0.5 Amperes, but when it’s removed, the activity goes down to zero. Thomas states that the resonant circuits are put at the center of the pyramid, at 1/3 of its height.

Working Magnetic Motor Demonstrated at Delft Unive...

This is something I’ve been expecting for a while. Magnetic motor news have been spread all over the world and the internet, with all kinds of possible setups and pseudo-inventors that had claimed themselves to be the center of all science, to have had discovered the configuration in which magnets could become monopolar and run a motor that did useful mechanical work.

An inventor from Turkey, Muammer Yildiz, as Overunity.com and PESN.com report, has just demonstrated his own version of a magnetic motor at the University of Delft, in the Netherlands, in front of an audience made of university staff and students. His device ran for more than 10 minutes, rotating a fan. The wind speed was measured and it has been concluded that the power of Yildiz’s magnetic motor is about 250 W.
Suspicions of a battery hidden in the device do exist, but to catch everyone’s attention and prove this was no fake, Yildiz gave his magnetic motor to the students to break apart and study it. PESN reports that another demonstration is to be kept May 12, somewhere in Germany. Watch the video and see for yourself. If his machine works, there are no hidden tricks and the magnets will last for as long as to produce useful energy at a cheap price, then we’ll have an energy revolution… maybe.

Yildis had already shown his device on a Turkish television:

How to Build a Gravity Engine: The Pinwheel Free E...

Pinwheels have been used for many things along history. One of the most interesting uses I’ve ever seen is making a pinwheel act as a free energy generator, powered by gravity.

The inventor of this (unknown) or some other free energy fan has posted an explanation of how the Pinwheel Free Energy Generator might work, on a Squidoo lens. Another website I found hosted the schematics that may help one build the generator. I compiled both and put them into this article.
I really don’t guarantee whether it will work or not, but I’m eager to find anybody who tried it and their results. Gravity is one of the disputed possible sources of energy that, if harvested properly and if working, would change the way we see things – forever.
So, here’s how the pinwheel generator supposedly works:
“As the weight ball in the lower cylinder descends, it forces the liquid out of the cylinder, through the Pelton wheel (turning the wheel and the generator), and into the upper cylinder. As the ball nears the bottom of the cylinder, the liquid weight of the mechanism is concentrated in the upper and right side cylinders, over-balancing the mechanism to rotate to the right when unlocked.
As the ball presses down on the unlocking mechanism, it also compresses the push bar spring. If the ball weighs 60,000 lbs, the energy in the spring can equal 59,999 lbs. Once the ball unlocks the mechanism, the spring bar pushes the lower cylinder out of the stop block. This push, along with the over-balance, causes the whole mechanism to rotate 90 degrees to where the right side cylinder becomes the lower cylinder, having now its ball begin its descent-producing electricity.
This process continues perpetually. An air venting pipe connects the cylinders that are opposite to each other so that as the liquid enters the top cylinder, the air it is displacing goes out the pipe and into the bottom cylinder, being assisted by the vacuum being created in the bottom cylinder by it’s ball descending.
This mechanism can function because the laws of entropy prevent only singular mechanisms from performing perpetually because they need to use the energy they produce to recycle themselves. Being a compound mechanism, this generator does not. The energy is generated, gravity rotates it.”
If any of you tried this experiment and it did or did not work, please comment. Also, if you have an opinion after seeing the schematics presented below, say your thoughts.

Serbian Overunity Device: Free Energy from Gravity...

From ancient times, people have been trying to find out the perfect energy producing machine. For that purpose, brilliant minds put themselves to work and researched the most sophisticated mechanical machines ever. Until nowadays, no such machines have broken through the filter of time, and no such wonderful inventors are known to have made the over unity device.

Still, there is a doubt: it seems certain interest groups from the 20th century and today still have a problem with ones who invent anything that goes very efficient, and reduces the consumers’ energy costs, free energy machines included. If you have been paying attention, there are a lot of interesting and breakthrough inventions that you only hear about, but that don’t succeed getting out on the market, or are proven suddenly, with no presentable evidence, that they are fakes.
All I know is that there is no smoke without fire, and there are a lot of non-interested people claiming the same thing.
For example, this man from Serbia, Veljko Milkovic, appears to have invented a device that does overunity: it outputs more energy than inputted, apparently violating Newton’s Third Law of Motion: “For every action there is an equal and opposite reaction.”
It seems Veljko’s machine uses the gravitational force for its power source, thing that others have also claimed.
“This gravity machine has only two main parts: a massive lever and a pendulum. The interaction of the two-stage lever multiplies input energy into output energy convenient for useful work (mechanical hammer, press, pump, transmission, electric generator…).”

Video of a Working Homemade Linear Magnetic Motor

I accidentally stumbled upon this three-year-old video today, watched it and realized that the guy has just demonstrated what many people don’t believe or want to believe: that magnetic motors exist, work and can provide useful effects to humanity.

This is a demonstration of a linear magnetic motor in which the experimenter puts a piece of magnet at one of its ends and the magnet travels by itself, or should I say, with the help of the other magnets surrounding it, to the other end of the machine.
What’s to note in this video is that the shuttle magnet stops before reaching the other end. However, if there would be no end to it, the magnet would travel indefinitely.
The guy who made this linear magnetic motor explicitly says at the end that it’s nevertheless possible to reproduce the machine in a circular form and make it ever-spinning.

Schematic of How to Build a Magnetic Motor

Many have tried building a magnetic motor. I am seeing a lot of scammers in my daily quest to alternative energy, but what I have learned is that energy is not free, perpetual motion machines do not exist, everything is taken from somewhere and put elsewhere.

There also is this so-called “free energy“, the zero-point energy, proven mathematically by many scientists. My duty as a green optimistic is to collect everything I see someone has struggled explaining and demonstrating, put it in one place and let the people see and comment. Such is the example of this magnetic motor.

But there are also “green pessimistic” websites. When they see something out of “common sense” boundaries, they freak out and scream something like”omg, this can’t be real! I need no proof! I must not think of this! Perish, Satan!”

I took such an article today as an inspiration because it talks about a magnetic motor, one of my favourite subjects, about which I haven’t heard much lately.

Here is the whole process of transforming the magnetic energy into mechanical energy, explained by the invetion’s author (Sandeep Acharya):

“Think of Two Powerful Magnets. One fixed plate over rotating disk with North side parallel to disk surface, and other on the rotating plate connected to small gear G1. If the magnet over gear G1′s north side is parallel to that of which is over Rotating disk then they both will repel each other. Now the magnet over the left disk will try to rotate the disk below in (think) clock-wise direction.

Now there is another magnet at 30 angular distance on Rotating Disk on both side of the magnet M1. Now the large gear G0 is connected directly to Rotating disk with a rod. So after repulsion if Rotating-Disk rotates it will rotate the gear G0 which is connected to gear G1. So the magnet over G1 rotate in the direction perpendicular to that of fixed-disk surface.
Now the angle and teeth ratio of G0 and G1 is such that when the magnet M1 moves 30 degree, the other magnet which came in the position where M1 was, it will be repelled by the magnet of Fixed-disk as the magnet on Fixed-disk has moved 360 degrees on the plate above gear G1. So if the first repulsion of Magnets M1 and M0 is powerful enough to make rotating-disk rotate 30-degrees or more the disk would rotate till error occurs in position of disk, friction loss or magnetic energy loss.

The space between two disk is just more than the width of magnets M0 and M1 and space needed for connecting gear G0 to rotating disk with a rod. Now I’ve not tested with actual objects. When designing you may think of losses or may think that when rotating disk rotates 30 degrees and magnet M0 will be rotating clock-wise on the plate over G2 then it may start to repel M1 after it has rotated about 25 degrees, the solution is to use more powerful magnets.

If all the objects are made precisely with measurements given and the rectangular cubic magnets are powerful enough to rotate more then 30 degrees in first repulsion then the system will work.

Here friction and other losses are neglected as magnets are much more powerful. But think of friction between rotating disk and Shaft, it can be neglected by using magnetic joint between them.

On the left primary measurements of needed objects are given. If you find any reason of not running this mechanism let me know.”

It seems to me that this is basically the Perendev magnetic motor presented in the same-named category of our blog.

What do you think? Could it work?